When you use the prolific devices in windows 10, there will a common error is that your devices cannot work properly because of the code 10 error. And in device manager, you will see the prolific usb to serial device as a yellow exclamation.
Welcome to the PC Matic Driver Library, the internet's most complete and comprehensive source for driver information. Prolific. Product. Windows 10 64-Bit.
As you can see from your real case, you open the device manager, but to find there is a yellow exclamation next to the Prolific USB TO Serial Comm Port (COMS).
Obviously, if you double-click on it, you will see:
The Device status shows you This device cannot start. (Code 10). Now you will have known well about the troubles with the Prolific USB to the Serial driver on Windows 10.
Of course, you can try to manually update the driver at Prolific site: Download drivers from Prolific site. But, look carefully on this page and you will read an important notice in RED: Windows 8/8.1/10 are NOT supported in PL-2303HXA and PL-2303X EOL (End Of Life) chip versions. When you upgrade your older Windows system to the latest Windows 10, or perform updates directly on Windows 10, the Prolific USB to Serial driver also gets update, and if it doesn’t work with your old hardware, you might have the problem. So you can try to downgrade your Prolific USB to Serial driver. Here’s how you can do it.
Or sometimes, you will also see the USB mass storeage with code 10 error.
The Prolific USB to serial Issue will also show messages like this:
'This Device cannot start (Code 10)'
'No driver installed for this device'
'Device driver was not successfully installed'
No matter what is the real case for you, it is urgent to solve this error code 10 instantly.
If you are more familiar with the Prolific USB to Serial drivers, maybe you can know exactly why you should take some measures at once.
What is the Prolific USB to Serial on Windows 10?
It is developed by Prolific to offer interface bridge solution to connect your legacy peripherals and application on Windows, Mac, Linux, and Android system.
Now you can know how important it is on your PC.
Why the Prolific USB to Serial error happens to Windows 10?
The Prolific 64-bit drivers that Microsoft supplies via Windows Update, Versions 3.4.67.325, 3.4.25.218, 2.1.51.238 and 3.4.62.293 - cannot work with most adapters, thus showing the generic 'Code 10' error.
How to Fix the Prolific USB to Serial Driver cannot Start Windows 10?
On the basis of the above analysis, it is apparent that the Prolific USB to Serial Comm Port driver is the main cause of this code error 10 on Windows 10.
Therefore, resolving the Prolific USB to Serial driver issue can be the most effective and efficient methods.
Solution 1: Update Prolific USB to Serial Driver in Device Manager
Device manager is also ready for you to update all the device drivers for Windows 10, here you want to update the Prolific USB to Serial drivers is no exception.
1. Unplug all USB-To-Serial adapters from your computer.
2. Open Device Manager.
3. Expand Ports (Com & LPT) and then right-click Prolific USB-to-Serial Comm Port (Com5) to Update Driver.
Here in your computer, maybe it is another comm port.
4. Choose to Search automatically for updated driver software.
Windows 10 will search the latest of prolific USB to the Serial driver for your PC. And with it, the code 10 error cannot start will not occurs to your Prolific USB to Serial devices.
While if your computer still cannot be installed with the newest Prolific USB to Serial drivers with this way, you can try to navigate to the Prolific official site to download the recently released driver on Windows 10.
Solution 2: Update the Prolific USB to Serial Driver Automatically
Sometimes, the Prolific site will not upload the Prolific USB to USB Serial devices regularly for Windows 10. Or on the other hand, you even cannot find your device model there.
Or simply to enjoy the convenience brought by the tool — Driver Doctor. You can decide to update the prolific USB to Serial drivers in an automatic way.
1. Download and run Driver Doctor on Windows 10.
2. Hit the button Scan Now, Get Drivers and Download All one by one.
In this process, Driver Doctor will scan for your PC until downloading the outdated or incompatible drivers on Windows 10, including the prolific USB to Serial driver.
It will only take you little time to use Driver Doctor to download the updated Prolific USB to Serial drivers.
At this moment, you are capable of checking if there is also a warning close to the Prolific USB to Serial Comm Port in Windows 10 device manager.
Solution 3: Troubleshoot the Prolific USB to Serial Devices
If the ways above are useless for you, maybe you have to use hardware and devices troubleshooter for Windows 10 to pinpoint the causes for the code error 10 with Prolific USB to Serial Comm Port.
1. Go to Start > Settings > Update & Security.
2. Under Troubleshoot, scroll down to find out Hardware and Devices to Run the troubleshooter.
This troubleshooter can let you know whether there are any problems with your Prolific USB to Serial devices.
If there are, Windows 10 can fix some the errors for you automatically.
In a word, code 10 error This device cannot start happens to the Prolific USB to Serial device drivers or the Realtek HD audio, it is proved feasible to try the solutions in this post accordingly on Windows 10.
News From
Category: Computer Repair and Service Profile: windows10skill.com is an website to teaches people how to customize their Windows 10 system settings, hardware settings, fix the system errors and hardware errors.
For more information:
Make an Inquiry about this reportHERE!- windows10skill.com
- windows10skill.com/fix-cod…windows-10
- windows10skill.com/windows…ot-working
- windows10skill.com/fix-usb…windows-10
- windows10skill.com/downloa…ndows-1087
- windows10skill.com/fix-usb…rt-code-10
Product Description
K150 is a low-cost high-performance PIC programmer, supporting many popular PIC chips. Allows reading, writing, encryption, and uses high-speed USB communication for fast programming ( speed average PICSTART + 3-5 times ). Fully automatic programming checksum ; equipped with 40pin DIP programming ZIF socket, direct programming of 8pin-40pinDIP chip; 8pin-40 pin chip as well as via the onboard the ICSP interface. Popular download software available; software-compatible the Windows98 and Windows2000/NT, Windows XP/windows7 operating system. Socketed chips for easy replacement and upgrade.
Please also check out our quick start guide to using the Great Cow Basic IDE with this programmer here:
http://forum.hobbycomponents.com/viewto ... 106&t=1688
Order Yours Here.
Features:
Support many popular PIC chips, programming, read, encryption and other features!
No external power supply required, communication and power by supplied USB cable.
Much faster programming rate than PICSTARTPLUS .
Can easily read the contents of the chip program area.
With 40pin ZIF socket, 8-pin to 40 pin PIC microcontroller chip can easily be programmed.
8 pin 40 pin-board Allows programming of PIC device whilst in circuit via its ICSP and included cable.
Compatible with Windows98 and Windows2000/NT, Windows XP / Windows 7 and other operating systems.
PLEASE NOTE THAT THIS PROGRAMMER IS NOT CURRENTLY COMPATIBLE WITH WINDOWS 8.x and above
UPDATE: For Windows 8/8.1/10 users we have a tested and working driver. However this is an unofficial driver version and although we have tested and confirmed it to work a a Windows 10 system we provide no warranties or guarantees that it will work with your system. The driver can be found towards the bottom of this post. We value your feedback on this fixed driver.
Package Includes:
1x K150 Pic Programmer
1x USB Cable 1x ICSP Cable
Windows software:
Windows Drivers:
Windows drivers for windows XP/7 can be downloaded here.
An unofficial driver version (please see note at the top of this post before installing) for Windows versions 8, 8.1, and 10 can be downloaded directly from our forum here:
Quick setup guide:
Prolific Driver 3.2.0.0 Windows 10
1) Download and install the appropriate driver then attach the K150 programmer.
2) Download the PIC Program Software English Version.zip zip file to your computer and then unzip it.
3) Inside the unzipped folder you will see the microbrn software called microbrn.exe. Double click this and the microbrn programming software should open up.
4) Set the COM port for your K150 programmer by going to File->Port and enter the COM port number in the window that opens up (you can find the COM port number from windows file manager).
5) Make sure that the correct programmer type is selected by going to File->Programmer and selecting K150
6) From the main window select your PIC device from the Chip Selector drop down selection. Microbrn should then show you where on the ZIF socket (or ICSP header) you should place your PIC.
7) Next load in your hex file by going to File->load
8) Finally you can upload your hex file to your PIC device by clicking the program button int he main window.
Note that if your hex file doesn't contain fuse settings you can set them by clicking the Fuses button before uploading to your PIC
Known issues and solutions:
When attempting to program the EEPROM of my device I get a reset error and the programmer fails to program the device.
This is caused by an incorrect setting in the Pic programming software's configuration file. To fix this problem locate the file named ‘chipdata.cid’ which should be in the same folder as your microbrn software. Edit this file with a text editor and locate the setting's for your particular device. Amongst these settings you will find a value for ProgramDelay. Keep increasing this value by 10 until you are able to program your device's EEPROM. Please note that you will need to restart the software each time you edit this file.
The microrn software keeps saying I have the wrong COM port
This problem is normally caused because the microbrn software doesn't like high COM port numbers. If the COM port of your programmer is above COM9 you can lower it by doing the following:
Make sure the programmer is plugged in.
In windows open up device manager (click start and type dev man in the search box)
Find the COM port for the programmer under Port (COM & LPT)
Right click on it and select properties
In the window that opens click the Port Settings tab
Click the Advanced button
In the COM port number drop down box change the COM port number to a lower value
They will probably all say they are 'in use' but so long as you don't have any hardware attached that is currently using that particular COM port it's fine to choose it.
Click OK to close the two windows and then close device manager.
Unplug the programmer and reattach it.
Then restart microbrn.
I am using Windows 8/10 and I can't get the programming software to talk to the programmer. What am I doing wrong?
Baofeng Prolific Driver Windows 10
Currently the K150 does not work with Windows versions above Windows 7. This is due to the fact the latest versions of the Prolific USB driver no longer support the PL2303-HX version of the USB interface chip that is installed on the K150. Whereas installing an older version of the driver would normally resolve this issue, unfortunately Windows versions 8 and above will immediately update the driver to the latest and incompatible version without any notification. At the moment we not aware of a workaround for this issue however we will update this post should we find one. Update: Please see the note found at the top of this post for a solution.Remove Prolific Driver Windows 10
Disclaimer: Libraries, example code, and diagrams are provided as an additional free service by Hobby Components and are not sold as part of this product. We do not provide any guarantees or warranties as to their accuracy or fitness for purpose.Descriptions and diagrams on this page are copyright Hobby Components Ltd and may not be reproduced without permission.